248-936-0300
Dramatically decrease chemical, packaging, labor and waste with the innovative Phazer™ Mobile Floor Care System. With this system the operator carries floor finish in a self-contained carrier and uses an ergonomic flat mop to apply finish.
Features & Benefits:
- Ergonomic design eliminates bending, reaching and wringing out string mops.
- Ergonomic applicator mop design minimizes awkward stance.
- Completely contained system minimizes operator contact with chemicals
- Flexible, collapsible pouches create 83% less plastic waste than 5-gal pail system.
- Innovative valve design ensures excess product in feed line runs back into product bag for later use, minimizing product waste up to 20% over traditional mop and bucket.
- Fluid, uninterrupted motion eliminates the disruption of rewetting a string mop, enabling workers to increase productivity up to 73% over mop and bucket system.
Directions for Use:
Loading the Product Bag:
- Open pack cover by releasing the plastic buckle on the locking strap. Note the orientation of the product bag and the bag spout.
- Place the product bag into position and slide the inside slot of the bag collar into the slot on the pack.
- Push the collar completely down and snap into place as shown. This will help hold the collar at its most downward point during use to insure complete product evacuation.
- Remove the shipping dust cap to gain access to the self sealing bag insert.
- Attach the delivery tube connector as shown by threading onto the bag spout.
- Turn until it is completely engaged.
- Rotate the pack cover closed and secure the locking strap.
Connecting the Applicator Handle to the Applicator Head:
- Insert the stationary pin on the connector clip into one of the center holes on the applicator head.
- Slide the bolt of the moveable pin back and rotate the connector into position. Release the sliding bolt to secure the connector to the applicator head.
Preparing the Applicator Pad:
- It is always best to pre-moisten the applicator pad. This will help to saturate the pad with finish during initial use.
- If you are using a new pad, rinse it thoroughly several times.
- Ring out the excess water so the pad is left damp. Always inspect the pad to ensure that all fibers and lint have been removed, especially if it is a new pad.
- Center the damp pad onto the applicator head. Press firmly into place.
Additional Notes:
- For application techniques, proper use and additional directions for use, refer to the Phazer Installation and Operation Manual and the specific product(s) I&O Manual
Lead times for this product may vary - direct ship from manufacturer
Description
Dramatically decrease chemical, packaging, labor and waste with the innovative Phazer™ Mobile Floor Care System. With this system the operator carries floor finish in a self-contained carrier and uses an ergonomic flat mop to apply finish.
Features & Benefits:
- Ergonomic design eliminates bending, reaching and wringing out string mops.
- Ergonomic applicator mop design minimizes awkward stance.
- Completely contained system minimizes operator contact with chemicals
- Flexible, collapsible pouches create 83% less plastic waste than 5-gal pail system.
- Innovative valve design ensures excess product in feed line runs back into product bag for later use, minimizing product waste up to 20% over traditional mop and bucket.
- Fluid, uninterrupted motion eliminates the disruption of rewetting a string mop, enabling workers to increase productivity up to 73% over mop and bucket system.
Directions for Use:
Loading the Product Bag:
- Open pack cover by releasing the plastic buckle on the locking strap. Note the orientation of the product bag and the bag spout.
- Place the product bag into position and slide the inside slot of the bag collar into the slot on the pack.
- Push the collar completely down and snap into place as shown. This will help hold the collar at its most downward point during use to insure complete product evacuation.
- Remove the shipping dust cap to gain access to the self sealing bag insert.
- Attach the delivery tube connector as shown by threading onto the bag spout.
- Turn until it is completely engaged.
- Rotate the pack cover closed and secure the locking strap.
Connecting the Applicator Handle to the Applicator Head:
- Insert the stationary pin on the connector clip into one of the center holes on the applicator head.
- Slide the bolt of the moveable pin back and rotate the connector into position. Release the sliding bolt to secure the connector to the applicator head.
Preparing the Applicator Pad:
- It is always best to pre-moisten the applicator pad. This will help to saturate the pad with finish during initial use.
- If you are using a new pad, rinse it thoroughly several times.
- Ring out the excess water so the pad is left damp. Always inspect the pad to ensure that all fibers and lint have been removed, especially if it is a new pad.
- Center the damp pad onto the applicator head. Press firmly into place.
Additional Notes:
- For application techniques, proper use and additional directions for use, refer to the Phazer Installation and Operation Manual and the specific product(s) I&O Manual
Lead times for this product may vary - direct ship from manufacturer
Reviews
Item Added to Your Cart
Customers also bought...
Item Added to Your Cart
Customers also bought...
Item Added to Your Cart
Customers also bought...
Related Products
3
visitors right now
3
visitors have this item in their cart right now
3
people have bought this item
3
% of people buy 2 or more